OnTheClock is 100 web-based and trusted by more than 15,000 companies with a 4.8 star rating. The GII will ask you to enroll two fingers, enroll the first, then the second. An employee time clock system that offers a powerful and accurate solution for small businesses to track in-house and remote employee hours worked for payroll. Your first enrollment will be for the administrator of the clock. Select the Bio Enroll button on the lower right hand side. Your clock is now ready for admin configuration Your clock will go through a setup screen and connect to the time management system. Employees can use the keypad to view their time in the current and previous pay periods, approve their time, and view leave time balances. Make sure that your clock is connected to a power supply and turned on. (Model: Genus G1) The Genus G1 electronic time clock data terminal integrates with ExecuTime Time & Attendance and provides essential time tracking functionality for staff and managers.
#GENUS II DEFAULT LOGIN TIME CLOCK FULL#
Depending on the degree of charge, the UPS may require power for up to 20 hours to obtain full charge. Note: New UPS Modules may be shipped less than fully charged.
Should the yellow LED be lit the disconnect switch must be pressed again. Momentarily depress the disconnect switch located on the top of the UPS to ensure the battery is disconnected.Installations with UPS option - When a UPS is part of the Terminal installation, the UPS is pressed firmly into the Terminal base until it snaps in place, and the spring tab makes contact with the inside top of the base. Wait until the entire installation is completed before plugging the power pack into an AC 110 volt outlet. Power Pack - Plug the power pack (if supplied) into the G2 Terminal power port. Ethernet Connection – Plug the Ethernet CAT-5 cable into the Ethernet Port (distinguished by the silver connector).was the time of eating the chief meal this hour was three o'clock. Sixty two samples of Sanghuangporus species from Europe, North America. The one identified in the picture below is for the Ethernet Connection. A word that denies or renders negative the second or subsequent part of a propo-. In fact, it represents a group of fungi belonging to the genus Sanghuangporus. The back of the Genus® terminal provides connections for many installation options. Using an ohmmeter, check to see if the ground bus and base unit are attached to the ground wire.Įthernet Connection and UPS / Power Connections.Add a lock washer above the ring terminal then replace the nut. Reassemble - Place the ring terminal on the ground stud above the ground bar.Crimp a #6 ring terminal to a 16 gauge or larger wire, which is to be run to an appropriate grounding point outside of the G2 terminal.Remove the nut from the #6 stud from the ground bus bar.Connect the wire to a suitable building ground, such as a driven ground rod.Note: In high ESD situations and additional ground wire is recommended The base must be within six (6) feet from a power outlet if a power pack is being used in the installation (see input power requirements). The recommended height for the terminal base is four feet above the floor.Securely attach the 2062 to the wall using an appropriate anchor method for the wall construction. Use the 2062 terminal base as a template to locate the mounting holes.Remove knockouts required for your installation before mounting the base. If needed, an antenna knockout is at the top right of the base. There are two 7/8” knockouts located at the bottom of the 2062 terminal base.The unit is prepared for wall mount installation and has two 7/8” and one 1” pre-cut access holes for cables to enter the enclosure from the rear.In this part, some of the important constraints like false paths, multicycle paths, maximum delay and minimum delay are defined. If no -max or -min value is specified, maximum and mimum output delays are assumed to be equal. In above command -max value refers to the longest path and -min value refers to the shortest path.
#GENUS II DEFAULT LOGIN TIME CLOCK MANUAL#
: Date- Day Genus G2 User Manual UM3000-1 Date- Day 10. Press to highlight the hour field (Time is set to a 24-hour clock). From the options at the bottom of the display press to advance to and highlight Time. Set_output_delay 1.7 -clock Ībove command will set output delay 1.7 unit to all output ports with respect to the positive edge (default edge) of the CLK1. : Time Setup Genus G2 User Manual UM3000-1 Time Setup Time 1. Output ports are assumed to have zero output delay if it is not specified. Set_output_delay command sets output delay requirements on an output port with respect to the clock edge. Set_output_delay delay_value port_pin_list
0 kommentar(er)
